FPT Advances Hybrid Power and Biodiesel Technology for Off-Highway Machinery
FPT Industrial has introduced its third-generation F28 Hybrid powertrain and a prototype biodiesel conversion system, bringing two approaches to reducing diesel dependence into focus at EIMA International 2026 in Bologna, Italy. The developments are aimed at machinery manufacturers seeking to introduce alternative power technologies without undertaking extensive redesigns of established equipment platforms.
The new F28 Hybrid integrates an electric motor within the flywheel housing of a compact 2.8-litre diesel engine, providing series and parallel hybrid configurations through a 700 V electrical architecture. Alongside it, FPT demonstrated a conversion system intended to allow its N45 industrial engine to operate on pure B100 biodiesel, incorporating additional fuel management equipment to address some of the difficulties associated with the fuel.
Both technologies were presented at EIMA International, held from 10 to 14 November 2026, alongside updated conventional engines and power generation equipment. Although the exhibition primarily serves agricultural machinery manufacturers, several of FPT’s identified applications, including telehandlers, industrial power units and stationary generators, are equally relevant to the construction sector.
Briefing
- FPT introduced its third-generation F28 Hybrid with a 700 V electrical architecture.
- The hybrid offers series and parallel configurations, with up to 170 kW peak power.
- A prototype conversion kit is being developed to support B100 biodiesel operation.
- The N45 and F36 engines provide packaged power solutions for off-highway machinery.
- The updated CURSOR 13 G-Drive delivers up to 482 kW of standby mechanical power at 1,500 rpm.
Integrating Hybrid Power into Compact Machinery
The third-generation F28 Hybrid is based on a four-cylinder, 2.8-litre diesel engine producing 75 kW at 2,300 rpm and a maximum torque of 415 Nm at 1,600 rpm. Its electric motor is incorporated within the existing flywheel housing envelope, allowing FPT to introduce electrical assistance without significantly increasing the overall dimensions of the engine assembly.
Space is frequently at a premium in compact tractors, telehandlers and smaller industrial machines. Engine compartments must accommodate cooling equipment, exhaust aftertreatment, hydraulic connections and mechanical drive components, leaving limited room for the additional hardware associated with electrification. Modifying those arrangements can require changes to the chassis, driveline and vehicle structure, adding development costs that are particularly difficult to justify on lower-volume machinery platforms.
FPT’s integrated motor arrangement is intended to minimise this work. The system retains much of the conventional engine package while providing the electrical capability needed for hybrid operation, although manufacturers must still accommodate energy storage, power electronics and the associated control and thermal management equipment.
The 700 V architecture is available in series and parallel configurations, allowing manufacturers to select different arrangements according to their machinery requirements. In a series hybrid, the combustion engine can generate electricity while propulsion is provided electrically. A parallel arrangement allows combustion and electric power to contribute to the mechanical driveline, with the balance between them managed according to operating conditions.
FPT specifies 72 kW of continuous electric motor power at 2,300 rpm. The parallel configuration is rated at 147 kW maximum continuous output, rising to a peak of 170 kW, while the series architecture can support plug-in arrangements capable of fully electric operation.
These specifications offer flexibility for machines with widely varying power requirements. A telehandler, for example, may alternate between travel, lifting and stationary hydraulic operations, creating opportunities to manage engine loading through electrical assistance. The resulting fuel consumption and operating performance will depend on how the complete powertrain is configured and controlled.
The F28 Hybrid is also compatible with hydrotreated vegetable oil (HVO), offering an additional fuel option for applications where an approved renewable diesel supply is available. HVO differs chemically from conventional FAME biodiesel, and compatibility with one fuel does not automatically establish compatibility with the other.
FPT has not published comparative fuel consumption figures, battery specifications or operating duration for the hybrid system. Those details will become important as equipment manufacturers evaluate the technology for production machines, particularly where additional electrical components must be justified against expected operating savings.
Developing a Practical Route to B100 Biodiesel
While the F28 Hybrid introduces electrical power into a conventional engine package, FPT’s Biodiesel Conversion Kit prototype takes a different approach by addressing the fuel used in existing combustion technology.
Displayed alongside the N45 Stage V Industrial Power Unit, the system is designed to facilitate operation on B100 biodiesel, which consists entirely of fatty acid methyl esters (FAME). The fuel can present handling and storage challenges that are less pronounced with conventional diesel, particularly in relation to oxidation, moisture absorption, low-temperature behaviour and degradation during extended storage.
These characteristics can complicate its use in off-highway machinery, where equipment may operate intermittently, remain parked between assignments or work in locations with significant seasonal temperature variations. Fuel condition becomes especially relevant when an engine is expected to start reliably after a period of inactivity.
FPT’s prototype incorporates a dedicated fuel circuit and control unit, together with a preheating arrangement for cold-weather operation. It also provides automatic switching between diesel and B100, followed by an end-of-mission cleaning process intended to prevent biodiesel remaining stagnant within the engine’s fuel system.
The conversion equipment is designed to connect to existing fuel circuits without requiring changes to the original OEM engine hardware. FPT developed and tested the prototype with support from the Iveco Beyond Lab start-up accelerator, although the company has not announced a commercial introduction date or released detailed operational test results.
The N45 Industrial Power Unit used for the demonstration is a 4.5-litre, four-cylinder engine producing 125 kW at 2,200 rpm and 712 Nm of torque at 1,500 rpm. It incorporates a pre-assembled cooling package, air cleaner and FPT’s HI-eSCR2 selective catalytic reduction exhaust aftertreatment system, providing manufacturers with a largely integrated power unit.
The engine operates without exhaust gas recirculation and has a manufacturer-specified 600-hour service interval. Its packaged configuration is suitable for industrial machinery in which the engine drives hydraulic equipment, mechanical systems or electrical generation rather than conventional vehicle propulsion.
Combining the biodiesel conversion equipment with an established engine platform could offer a route for manufacturers and equipment operators wishing to introduce alternative fuels while retaining familiar machinery architectures. However, the system’s retrofit potential will depend on engine compatibility, applicable certification requirements, fuel quality and the results of further testing.
The prototype remains a development project rather than an approved universal conversion solution. Its commercial prospects will be influenced by the availability and cost of B100, particularly in markets where machinery already operates on conventional diesel or approved HVO fuels.
F36 Provides a Compact Conventional Alternative
FPT also presented the F36, a 3.6-litre four-cylinder engine positioned between its light- and medium-power ranges. Producing up to 105 kW at 2,300 rpm and 600 Nm of torque at 1,500 rpm, it is intended for applications including compact and speciality tractors, telehandlers and stationary equipment.
The engine has a dry weight of 320 kg and measures 702 mm in length, 614 mm in width and 898 mm in height. Its relatively compact installation envelope allows manufacturers to accommodate substantial mechanical power without making the engine the dominant factor in vehicle dimensions.
FPT has concentrated on service accessibility as well as performance, incorporating a single-side maintenance layout and compact HI-eSCR2 exhaust aftertreatment equipment. A 600-hour oil-change interval is specified, with the aftertreatment system designed to minimise routine maintenance requirements.
For machinery operating continuously under demanding loads, conventional diesel power remains an established option. The F36 provides manufacturers with a relatively compact mechanical power source where the additional components associated with hybrid or fully electric propulsion may offer limited operational advantages.
CURSOR 13 Targets Heavy-Duty Power Generation
At the heavier end of its EIMA presentation, FPT introduced an updated CURSOR 13 G-Drive engine for stationary power generation applications.
The 12.9-litre six-cylinder engine incorporates electronic common rail fuel injection operating at 1,600 bar, together with revised turbocharging and cooling systems intended to improve performance under demanding environmental conditions. FPT states that the engine can operate without power derating in severe heat, although the precise ambient temperature and installation limits are application-dependent.
At 1,500 rpm, the CURSOR 13 G-Drive delivers standby mechanical power ratings ranging from 330 to 482 kW, with prime power between 300 and 442 kW. Versions operating at 1,800 rpm are also available, extending the engine’s suitability to generator installations operating at different electrical frequencies.
The power unit is supplied with pre-assembled cooling and air filtration equipment, reducing the installation work required by generator manufacturers. Its 50 Hz and 60 Hz operating capability also provides flexibility for suppliers serving international markets with different electricity standards.
Construction projects frequently depend on temporary or independent power generation, particularly during early site development or when working in remote locations. Large generator sets may support pumping equipment, site facilities, processing operations and other substantial electrical loads, with reliability and maintenance access often taking precedence over engine packaging.
FPT specifies a 600-hour service interval for the updated CURSOR 13 G-Drive, which is designated for markets without the emissions requirements applicable to the company’s Stage V industrial engines. Generator manufacturers and project operators must therefore establish the appropriate regulatory and technical specifications for each installation.
Emissions Compliance and Alternative Fuels
The F28 Hybrid, N45 and F36 are identified by FPT as complying with Stage V and Tier 4 Final requirements, while the particular CURSOR 13 G-Drive variant displayed at EIMA is intended for unregulated markets.
Within the European Union, Regulation (EU) 2016/1628 establishes pollutant emission limits and type-approval requirements for engines used in non-road mobile machinery, including construction and agricultural equipment. Stage V addresses regulated exhaust pollutants such as nitrogen oxides and particulate matter rather than directly measuring the complete greenhouse gas impact of a machine.
Hybrid technology may reduce fuel consumption by changing how combustion engines respond to variable loads, while renewable fuels can offer lifecycle greenhouse gas reductions depending on their feedstocks, production processes and supply chains. The results depend on the application, and neither a hybrid designation nor compatibility with an alternative fuel provides a complete measure of environmental performance.
B100 also requires consideration of fuel standards, material compatibility, maintenance procedures and approved operating conditions. Introducing additional fuel management equipment may address some practical difficulties, but any conversion must still satisfy the relevant technical and regulatory requirements.
The absence of published comparative operating results for FPT’s latest hybrid and biodiesel systems leaves these questions open for equipment manufacturers considering production applications. FPT has established the technical configurations it intends to offer, with machine-level performance and commercial availability remaining the next stages of development.
Engineering Options for Existing Machinery Platforms
FPT’s EIMA presentation brought together hybrid propulsion, alternative fuels, compact industrial engines and heavy-duty power generation, reflecting the different operating demands found across off-highway equipment.
Electrification may be attractive for machinery with repeated changes in load or opportunities to recover and reuse energy, while conventional combustion engines continue to provide a practical option for applications requiring sustained mechanical output. Fuel compatibility and service infrastructure can be just as influential as rated power when equipment is expected to operate reliably over many years.
The F28 Hybrid and B100 conversion prototype share a practical engineering objective despite approaching it from different directions. Both attempt to introduce new energy technologies while preserving as much of the established engine and machinery architecture as possible.
For manufacturers working with existing vehicle platforms, that may prove more useful than starting with an entirely new machine.

Key Industry Questions
- What is the FPT F28 Hybrid engine? The F28 Hybrid is a 2.8-litre diesel-electric powertrain designed for compact off-highway machinery. Its third-generation design incorporates an electric motor within the flywheel housing and supports series and parallel hybrid configurations.
- How much power does the third-generation F28 Hybrid produce? The diesel engine produces 75 kW, while FPT specifies 72 kW of continuous electric motor power. The parallel configuration is rated at 147 kW maximum continuous output and 170 kW peak power.
- Which construction machines could use the F28 Hybrid? FPT identifies telehandlers among the potential applications, alongside compact, utility and speciality tractors. Other construction applications would require suitable mechanical and electrical integration by the equipment manufacturer.
- What is the purpose of FPT’s biodiesel conversion kit? The prototype is intended to support B100 biodiesel operation through fuel preheating, automatic diesel-to-biodiesel switching and fuel circuit cleaning, addressing handling and storage challenges associated with pure FAME biodiesel.
- Can the biodiesel conversion kit be retrofitted to existing engines? FPT states that the system is designed for installation within existing fuel circuits without altering original OEM engine hardware. Compatibility across different engines and commercial availability have not yet been established.
- What is the difference between HVO and B100 biodiesel? HVO is a paraffinic diesel fuel produced through hydrotreatment, while B100 consists of fatty acid methyl esters. Their chemical characteristics, storage requirements and engine compatibility differ, so approval for one does not automatically cover the other.
- Does hybrid technology automatically reduce machinery fuel consumption? No. Fuel savings depend on the operating cycle, energy storage system, electrical integration and powertrain controls. FPT has not published comparative fuel consumption figures for the third-generation F28 Hybrid.
- Where can the CURSOR 13 G-Drive be used? The CURSOR 13 G-Drive is intended for heavy-duty generator sets serving industrial facilities, construction projects and remote installations requiring independent electrical power. The version displayed at EIMA is designated for unregulated markets.
Strategic Takeaways
- Integrating the electric motor within the F28’s flywheel housing could allow manufacturers to introduce hybrid power without extensive changes to established machinery platforms.
- Series and parallel hybrid configurations give OEMs different ways to accommodate variable operating loads, although equipment-level efficiency remains to be demonstrated.
- FPT’s biodiesel prototype addresses practical fuel handling difficulties that can restrict the use of B100 in industrial engines, particularly during storage and intermittent operation.
- The continued development of conventional industrial engines reflects the importance of compact packaging, mechanical power density and accessible maintenance in off-highway equipment.
- Commercial adoption of the new hybrid and biodiesel technologies will depend on certification, operational testing, integration costs and the availability of suitable energy supplies.
















